'J' Cabinet Pull – 10" (254 mm) C/C, Stainless

The J254 is JWL’s ‘J’ Series cabinet pull at 10″ (254 mm) center to center: a hand-welded solid 304 stainless steel bar, squared ends, return on one side, thru-front mounted, projecting 1″ (25 mm). It is the size for pot drawers, wide base cabinets and dishwasher panels; the series runs 5″, 7.5″, 10″ and 12.5″ (126, 190, 254 and 318 mm) so one profile covers a whole kitchen. Designed and assembled in Vancouver, BC; in-stock orders ship in 1-3 workdays.

Specifications

Profile	‘J’ – squared ends, return on one side
Material	Solid 304 stainless steel, hand-welded
Bar section	1/2″ x 1/4″
Projection (from door face)	1″ (25 mm)
Center to center	10″ (254 mm)
Mount	Thru-front, 2 holes; 2 x 1 7/8″ break-off 8-32 screws included
Door thickness	Standard drawer and door fronts; included 8-32 screws break to length
Finishes	Brushed, Polished, Matte Black, Satin Brass PVD, White
Applications	Kitchen cabinets, pot drawers, wide base cabinets and dishwasher panels; bath vanities, laundry and closet millwork
Origin	Designed and assembled in Vancouver, BC
Shipping	In-stock orders ship in 1-3 workdays from Vancouver, BC; free shipping on orders over $500; ships to Canada and US
Warranty	Limited lifetime residential warranty on materials and workmanship (commercial: 5 yr brushed stainless, 2 yr coated). Full terms: jwlhome.com/warranty
Downloads	DWG (CAD), 3D model, PDF spec sheet

Profile

The ‘J’ profile has squared ends with the return on one side, with a curved underside that fills the hand. The bar section is 1/2″ x 1/4″, hand-welded from solid 304 stainless steel and finished in one piece with no visible fixings. Mount it with the return at the bottom on doors or to one side on drawers; the asymmetry reads as a deliberate detail across a run of fronts.

Sizing

Center to center is 10″ (254 mm); measure existing holes before ordering, because JWL’s ‘J’ spacing is in inches (126/190/254/318 mm), a few millimetres off the 128/192/256/320 mm metric standard. Use this size for pot drawers, wide base cabinets and dishwasher panels. As a rule of thumb, keep the pull at one-third to one-half of the front width and step sizes within the series.

Installation

Two 1 7/8″ break-off 8-32 screws are included. Drill two 5 mm holes at 10″ (254 mm) on center, snap each screw at the groove closest to the front thickness, and tighten from inside the drawer or door. Standard 3/4″ (19 mm) fronts need no extra hardware; for unusually thick fronts, buy longer 8-32 machine screws locally. DWG, 3D and PDF spec sheet downloads are on the page.

Frequently asked

Which ‘J’ Series size do I need, and what are the other sizes?

The J254 is 10″ (254 mm) center to center and suits pot drawers, wide base cabinets and dishwasher panels. The other ‘J’ Series sizes are 5″ (126 mm) at https://jwlhome.com/product/cabinet-pull-5-inch-center-to-center/; 7.5″ (190 mm) at https://jwlhome.com/product/cabinet-pull-7-inch-center-to-center/; 12.5″ (318 mm) at https://jwlhome.com/product/cabinet-pull-12-5-center-to-center/. All four share the same 1″ projection, 1/2″ x 1/4″ bar section and five finishes, so you can mix sizes across one kitchen without a visible change in profile.

Will this pull fit holes drilled for another brand?

Only if the existing holes are 254 mm (10″) apart. Many fronts are drilled to the metric standard (256 mm), which is a few millimetres off and will not align. For metric-drilled fronts choose the JWL ‘I’ Series; for new fronts, drill 5 mm holes at 10″ (254 mm) on center.

How far does the pull stand off the front, and will it clear appliances and adjacent doors?

Projection is 1″ (25 mm) from the front face to the outside of the bar, with roughly 3/4″ of finger clearance behind it. That is low enough to clear most fridge and dishwasher doors and to avoid clashing at inside corners, but check corner cabinets where two fronts meet at 90 degrees.

Do the finishes match JWL door handles and appliance handles?

Yes. Brushed, Polished, Matte Black, Satin Brass PVD and White are the same five finishes used across JWL’s ‘I’, ‘J’, ‘L’, ‘U’ and ‘P’ door handles, appliance handles and the ‘T’ Series knob, all on 304 stainless steel. Order every item in the same finish name and it will match; see the hardware samples page to confirm colour before a large order.

What is the lead time, and what warranty applies?

In-stock orders ship in 1-3 workdays from Vancouver, BC, to Canada and the US, with free shipping on orders over $500. JWL cabinet pulls carry a limited lifetime residential warranty on materials and workmanship; commercial use is covered 5 years for brushed stainless and 2 years for coated finishes. Full terms at jwlhome.com/warranty.